A Fridge Magnet
This is the implementation of the idea to create an electronic fridge magnet.
What is that?
- It is a battery operated Display
- A radio wireless connection provides the contents to show
It can be used as a "Internet of Things" implementation of a fridge magnet to show important or interesting information for the family, but can be used as a price/special offer label on the front side of shop shelves.
Features:
- It is possible to connect up to 31 displays to one same transmitter and update them independently (several displays sharing the same address will show the same contents).
- Using an optimized version of the code (currently under development) the circuit can work for monthes on a single battery. The display is bi-stable so it can turned off, the entire circuit can be put in sleep mode for the most part of the time.
Here is a picture of the prototype to whet your appetite:
The components used in this prototype are:
- a JeeNode v6 (18.5 euros)
- an e-paper display (29 euros)
- a 23k236 32KB RAM (1.61 euro)
- a jeelabs proto board (3.50 euros)
- AA Power Board (14.5 euros)
- pin stripes, copper wire, ...
- patience (unvaluable)
The total cost for a unit is around 70 euros (plus shipping costs from several suppliers etc).
The following parts are needed to upload the software and to send the images to our display (or to several displays):
- JeeLabs USB interface (13.5 euros)
- another JeeNode v6 (18.5 euros) or a JeeLink (32.5 euros).
RAM and wiring card
This card is the only hardware part than needs to be soldered. The current version, as shown in the picture here above, uses a JeeLabs proto board and insulated copper wired.
Here is the table of the connections:
Display Signal Connected to: AtMega pin: Equivalent Connector (JeeNode) "Arduino pin#" 1 GND GND(pin 3 any P port) GND GND 2 3.3V +3V(pin 4 any P port) +3.3V +3.3V 3 SCLK SCK(pin 3 SPI/ISP) SCLK/PB5 pin 19 13 4 MOSI MOSI(pin 4 SPI/ISP) MOSI/PB3 pin 17 11 5 MISO MISO(pin 1 SPI/ISP) MISO/PB4 pin 18 12 6 SSEL SEL0(pin 7 SPI/ISP) PB0 pin 14 8 7 Busy DIO4(pin 2 port 4) PD7 pin 13 7 8 BorderCtl IRQ (pin 6 any P port) PD3 pin 5 3 9 SCL SCL(pin 5 PWR/SEL/I2C) SCL/PC5 pin 28 A6 (19) 10 SDA SDA(pin 4 PWR/SEL/I2C) SDA/PC4 pin 27 A5 (18) 11 PWM DIO2(pin 2 port 2) PD5 pin 11 5 12 Reset DIO3(pin 2 port 3) PD6 pin 12 6 13 PWR SEL1(pin 8 SPI/ISP) PB1 pin 14 9 (**) 14 Discharge DIO1(pin 2 port 1) PD4 pin 6 4 (**: this pin has been remapped, it is not the same used in the demo code provided by Embedded Artists as PD2 is used by the RF12 radio tranceiver on JeeNodes). RAM pin Signal Connected to: ATmega PIN: Equivalent (JeeNode) "Arduino pin#" 1 /CS AIO2(pin 5 port 2) PC1 pin 24 A2 (15) 2 SO MISO(pin 1 SPI/ISP) MISO/PB4 pin 18 12 3 not connected 4 VSS/GND GND(pin 3 any P port) GND GND 5 SI MOSI(pin 4 SPI/ISP) MOSI/PB3 pin 17 11 6 SCK SCK(pin 3 SPI/ISP) SCLK/PB5 pin 19 13 7 HOLD +3V(pin 4 any P port) +3.3V +3.3V 8 VCC +3V(pin 4 any P port) +3.3V +3.3V